Speed: 0-350m/min

The equipment uses a DC motor and a tension controller to control the tension of the winding, and the speed can be synchronized with the host

Manual advance/retreat, round knife or straight knife cutting, flat end face, hexagonal positioning ruler to measure width, wide cutting width range, rapid positioning, simple operation, simple maintenance, economical and practical

This equipment is widely used for semi-automatic advance/retreat of masking paper, foam tape, double-sided tape, PE hose, paper tube, etc., round knife cutting, flat end face, hexagonal positioning ruler for measuring width, wide cutting width range, positioning Quick, easy to operate, simple to maintain, economical and practical

1. Frequency conversion speed regulation, manual/automatic tension control; 2. Ultrasonic automatic correction, transparent and opaque materials can be automatically detected without manual adjustment; 3. Automatically calculate the number of meters, set the number of meters, and automatically stop and break when the number of meters Automatic shutdown

The equipment adopts Delta servo motor, Delta PLC control system, 10" touch screen, Japan Yaskawa vector inverter, can freely set the strip width, the total width of the winding and the cross width of the winding. Servo winding speed Synchronize with the winding speed, automatic detection of winding diameter, length metering, constant linear speed operation, automatic unwinding tension, flat winding end surface,

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the air-cooled magnetic powder brake system controls the unwinding tension during the slitting process, and automatically decelerates to the meter. When stopping and unwinding to a small diameter, it will automatically decelerate and stop, and automatically calculate the diameter of winding and unwinding, with a diameter tolerance of ±1mm. The winding method is single-shaft winding, and the winding shaft adopts a special inflatable shaft. The slitting adopts a straight knife or a disc Knife,

The equipment adopts the German Siemens PLC control system, 10" touch screen, air-cooled magnetic powder brake system control: automatic tension for rewinding and unwinding, automatic deceleration and stop when reaching the meter, automatic deceleration and stop for unwinding to small coil diameter, automatic calculation of rewinding Roll meters and winding diameter. Anilox roller transfer coating method, two sets of ultrasonic automatic correction system, magnetic powder brake to control the tension of the raw material, pneumatic pressure roller, pneumatic back pressure scraper, the motor controls the scraper left and right during glue coating Swing and glue evenly

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the air-cooled magnetic powder brake system controls the unwinding tension during the slitting process, and automatically decelerates to the meter. When stopping and unwinding, it will automatically decelerate and stop, automatically calculate the diameter of rewinding and unwinding, and the diameter tolerance is ±1mm. The rewinding method is central surface rewinding, or single-shaft rewinding. The rewinding shaft adopts a dedicated air shaft or mechanical shaft. The slitting adopts straight knife or disc knife, and the corresponding knife can be selected for different thickness materials, and the slitting width can be adjusted arbitrarily.

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the air-cooled magnetic powder brake system controls the unwinding tension during the slitting process, and automatically decelerates to the meter. When stopping and unwinding to a small diameter, it will automatically decelerate and stop, and automatically calculate the diameter of rewinding and unwinding. The diameter tolerance is ±1mm. The rewinding method is central surface rewinding, or single-axis rewinding. The rewinding shaft adopts a special air expansion shaft for tape or Slip shaft. The slitting adopts straight knife or disc knife, and the corresponding knife can be selected for different thickness materials, and the slitting width can be adjusted at will. The system uses high-reliability electrical components, simple wiring, easy maintenance, high degree of automation, high efficiency, low noise and other advantages.

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the air-cooled magnetic powder brake system controls the unwinding tension and unwinding hydraulic pressure during the slitting process. Automatic feeding. Automatically decelerate and stop when it reaches the meter, and automatically decelerate and stop when unwinding to a small diameter. Automatically calculate the diameter of rewinding and unwinding, and the diameter tolerance is ±1mm. The rewinding method is central surface rewinding, and single-axis rewinding and rewinding are also possible. The reel adopts a special pneumatic shaft or a mechanical shaft. The slitting adopts a straight knife or a disc knife, and the corresponding cutter can be selected for different thickness materials, and the slitting width can be adjusted at will. The system adopts high-reliability electrical components, simple wiring, easy maintenance, high degree of automation, high efficiency, low noise and other advantages.

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the air-cooled magnetic powder brake system controls the unwinding tension and unwinding hydraulic pressure during the slitting process. Automatic feeding. Automatically decelerate and stop when it reaches the meter, and automatically decelerate and stop when unwinding to a small diameter. Automatically calculate the diameter of rewinding and unwinding, and the diameter tolerance is ±1mm. The rewinding method is central surface rewinding, and single-axis rewinding and rewinding are also possible. The reel adopts a special pneumatic shaft or a mechanical shaft. The slitting adopts a straight knife or a disc knife, and the corresponding knife can be selected for different thickness materials, and the slitting width can be adjusted at will. The system uses high-reliability electrical components, simple wiring, easy maintenance, high degree of automation, high efficiency, low noise and other advantages.

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, the air-cooled magnetic powder brake system controls the unwinding tension during the slitting process, and the unwinding belt is connected Material platform, automatically decelerate and stop when it reaches the meter, and automatically decelerate and stop when unwinding without material, automatically calculate the diameter of rewinding and unwinding, and the diameter tolerance is ±1mm. The rewinding method is central surface rewinding, or single-axis rewinding, and the special rewinding shaft is used. Inflatable shaft. The slitting adopts a straight knife or a disc knife, and the corresponding knife can be selected for different thickness materials, and the slitting width can be adjusted arbitrarily. The system uses high-reliability electrical components, simple wiring, easy maintenance, high automation, and high efficiency , Low noise and other advantages.

The machine adopts the German Siemens PLC control system, 10" touch screen, the uncoiler adopts servo motor drive, equipped with gear reducer; four sets of Siemens vector inverter and servo motor control the main traction and automatic winding tension; when the meter reaches the meter, it will automatically decelerate and stop. When unwinding to a small diameter, it will automatically decelerate and stop, and automatically calculate the diameter of rewinding and unwinding. The diameter tolerance is ±1mm. The rewinding method is central surface rewinding, or single-axis rewinding. The rewinding shaft adopts pure aluminum foil special air expansion shaft or machinery Shaft. The slitting adopts straight knife or disc knife, and the corresponding knife can be selected for different thickness materials, and the slitting width can be adjusted at will.

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, servo motors with the drive to control the unwinding tension during the slitting process, and automatically decelerate and stop when reaching the meter. When unwinding to a small diameter, it will automatically decelerate and stop, and automatically calculate the diameter of rewinding and unwinding, with a diameter tolerance of ±1mm.

The machine adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the Italian imported brake system controls the slitting process; it automatically decelerates and stops when it reaches the meter, and unwinds to small The winding diameter is automatically decelerated and stopped, and the winding and unwinding diameters are automatically calculated, and the diameter tolerance is ±1mm. The winding method is central winding or single-shaft winding. The winding shaft adopts a special air shaft. The system uses high

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, the Italian imported brake system controls the unwinding tension during the slitting process, and automatically decelerates and stops when it reaches the meter. When unwinding to a small diameter, it will automatically decelerate and stop, automatically calculate the diameter of rewinding and unwinding, with a diameter tolerance of ±1mm. The rewinding method is central surface rewinding, or single-shaft rewinding. The rewinding shaft adopts a special air expansion shaft. Straight knife or disc knife, you can choose the corresponding knife for different thickness materials, and the slitting width can be adjusted arbitrarily. The system uses high-reliability electrical components, simple wiring, easy maintenance, high degree of automation, high efficiency, low noise and other advantages

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, and the Italian imported brake system controls the unwinding tension during the slitting process, and automatically decelerates and stops when it reaches the meter. Rewinding to a small diameter automatically decelerates and stops, automatically calculates the diameter of rewinding and unwinding, and the diameter tolerance is ±1mm. The rewinding method is central surface rewinding, or single-shaft rewinding. The rewinding shaft adopts a special air shaft, embossing and dividing Cutting is carried out at the same time. The slitting adopts straight knife or disc knife, and the corresponding knife can be selected for different thickness materials, and the slitting width can be adjusted at will. The system adopts high-reliability electrical components, simple wiring, easy maintenance, high degree of automation, high efficiency, low noise and other advantages.

The equipment adopts the German Siemens PLC control system, 10" touch screen, three sets of servo motors with servo drives to control the main traction and automatic winding tension, one set of servo motors with servo drives to control the unwinding tension, and it will automatically decelerate and stop when it reaches the meter. When the coil diameter is small, it will automatically decelerate and stop, automatically calculate the diameter of rewinding and unwinding, and the diameter tolerance is ±1mm. The rewinding method is central surface rewinding, and the double rewinding shafts can independently control the tension. The rewinding shaft adopts a dedicated air expansion shaft. The cutting adopts power Small round knife, the slitting width can be adjusted arbitrarily, single or even number can be slit.

The equipment adopts German Siemens PLC control system, integrated machine design, easy to install, rewinding and unwinding on the same side, convenient for operation observation and driving unloading (reverse structure can also be customized according to customer needs, and CCD detection position is reserved); The diameter of unwinding and unwinding is calculated independently, no need to input the material thickness, the calculation accuracy of the roll diameter is ±1mm, the set number of meters will automatically decelerate and stop, and the unwinding will automatically decelerate and stop without material. The raw material is rolled up and automatically enters the host, saving time and effort; the unwinding is controlled by a servo motor, the tension signal is fed back, the running tension is stable, the unwinding mechanism is designed according to the size of the winding roll of the foil machine; the host adopts a set of servo motor drive and traction Pressure roller, precision knife groove roller, power small round knife is used for slitting, the slitting end surface is smooth and flat, no color difference, no burr, slitting part is equipped with dust suction device, winding is controlled by two sets of servo motors, winding tension signal feedback , The taper tension can be set, and the side material is automatically unloaded, which is convenient and quick. The electrical components of the equipment adopt well-known domestic and foreign brands, with high degree of automation, humanized operation, high efficiency, low noise, and stable performance.

The equipment adopts German Siemens PLC control system, split design, reverse operation of rewinding and unwinding, CCD detection and thickness gauge installed between unwinding and host; independent calculation of rewinding and unwinding diameter, no need to input material thickness, roll diameter calculation accuracy Within ±1mm, the set number of meters will automatically decelerate and stop, and the unwinding will automatically decelerate and stop; the unwinding adopts servo motor control, tension signal feedback, and the running tension is stable. The unwinding mechanism can be designed according to the size of the rewinding roll of the raw foil machine; It adopts a set of servo motor drive, equipped with traction pressure roller, precision knife groove roller, and the feed roller is equipped with a dust-sticking roller. The cutting adopts a small power round knife. The cutting end surface is smooth and flat without color difference. The cutting part is equipped with a dust suction device. The rewinding is controlled by two sets of servo motors, two sets of tension sensors and two sets of translation mechanisms are adopted, the tension running is stable, and the side material is automatically unloaded, which is convenient, fast, time-saving and labor-saving.